CAT ALLEYCAT 308 Ti QDModel: CAT/ALLEYCATCaliber: .308 CALOverall Length: 8.55"Diameter: 1.75"Min Barrel Length (Titanium): 10"Optimized Velocity: 2200 – 2900ft/sOptimized Platform: 20" M110A2Technology: Sniper2Recommendation: Precision RifleSpooky 1 added length: 6.63"Weight: 12.5 oz *Mount: 1x16LH QDFinish: DLC 

Inconel 718 QDModel: CAT/Alleycat (SURGE BYPASS)Caliber: 556NATOOverall Length: 6.10"Diameter: 1.60"Min Barrel Length (Inconel): 8"Optimized Velocity:1100 – 3200ft/sOptimized Platform: 14" M4Technology:Surge BypassRecommendation: Semi-AutoSpooky 1 added length: 4.23"Weight: 16.6 oz *Mount: 1x16LH QDFinish: DLC

6Al-4V Titanium QDModel: CAT/Alleycat (SURGE BYPASS)Caliber: 556NATOOverall Length: 6.10"Diameter: 1.60"Min Barrel Length (Titanium): 10"Optimized Velocity: 1100 – 3200ft/sOptimized Platform: 14" M4Technology: Surge BypassRecommendation: Semi-AutoSpooky 1 added length: 4.23"Weight: 9.0 oz *Mount: 1x16LH QDFinish: DLC

Inconel 718 “HUB”Model: CAT/ALLEYCAT (SURGE BYPASS)Caliber: 6 ARCOverall Length: 6.50"*Diameter: 1.60"Min Barrel Length (Inconel): 8"Optimized Velocity: 1000 – 2800ft/sOptimized Platform: 14.5" TSF ARCTechnology: Surge BypassRecommendation: Semi-AutoSpooky 1 added length: 4.58"Weight: 16.0 oz *Mount: 1.375x24 “HUB”Finish: DLC 

Inconel 718 QDModel: CAT/ALLEYCAT (SURGE BYPASS)Caliber: 6 ARCOverall Length: 6.50"Diameter: 1.60"Min Barrel Length (Inconel): 8"Optimized Velocity: 1000 – 2800ft/sOptimized Platform: 14.5" TSF ARCTechnology: Surge BypassRecommendation: Semi-AutoSpooky 1 added length: 4.58"Weight: 16.0 oz *Mount: 1x16LH QDFinish: DLC 

CAT ALLEYCAT 7.62 718 QDModel: CAT/ALLEYCAT (SURGE BYPASS)Caliber: 7.62×39 (Max 762NATO)Overall Length: 7.20"Diameter: 1.60"Min Barrel Length (Inconel): 8" (5.56Nato)Optimized Velocity:1100 – 2600ft/sOptimized Platform:16" AK47Technology: Surge BypassRecommendation: Semi-AutoSpooky 1 added length: 5.28"Weight: 19.7 oz *Mount: 1x16LH QDFinish: DLC 

CAT ALLEYCAT 7.62 Ti QDModel: CAT/ALLEYCAT (SURGE BYPASS)Caliber: 7.62×39 (Max 762NATO)Overall Length: 7.20"Diameter: 1.60"Min Barrel Length (Titanium): 10"Optimized Velocity: 1100 – 2600ft/sOptimized Platform: 16" AK47Technology: Surge BypassRecommendation: Semi-AutoSpooky 1 added length: 5.28"Weight: 10.6 oz *Mount: 1x16LH QDFinish: DLC 

CAT/NOAH/A1 Ti "HUB"Model: CAT/NOAH/A1Caliber: 6 ARCWeight Titanium: 8.6 oz (MIL) *Overall Length: 6.15”Diameter: 1.60"Min Barrel Length (Titanium): 10”Optimized Velocity: 1000 – 2800ft/sOptimized Platform: 14.5" TSF ARCTechnology: Surge BypassRecommendation: Semi-Auto 6mm (and 5.56)Finish: DLCMounting: 5/8×24 Direct Thread (Included) 

CAT/NOAH/A1 Ti QD1x16LH QD Model: CAT/NOAH/A1Caliber: 6 ARCWeight Titanium: 9.8 oz (MIL)*Weight Inconel: 19.3 OZ (MIL) *Overall Length: 6.50”Diameter: 1.60”Min Barrel Length (Titanium): 10”Min Barrel Length (Inconel): 8” (5.56NATO)Optimized Velocity: 1000 – 2800ft/sOptimized Platform: 14.5" TSF ARCTechnology: Surge BypassRecommendation: Semi-Auto 6mm (and 5.56)Finish: DLCMounting: Spooky 1 (Included)

DescriptionThe Diligent Defense Enticer L can comes with a removable end cap which is compatible with Dead Air end caps.Enticer cans also come threaded with 1-3/8"x24. What does 1-3/8×24 thread mean for you? This thread allows you to run a wide variety of mounts such as: Direct thread adapters, Q Plan B/Cherry Bomb, Keymo and Rearden Atlas. Enticer L SpecsCaliber: 7.62 NATO/ 300BK / 300WM or any caliber smallerDiameter: 1-5/8 (1.625”)Weight: 17.1oz with included mountOverall Length: 8-1/4?Material: 100% CNC machined 17-4 Stainless laser welded & heat treatedCommon Min Barrel Lengths556 – 10.5"308 – 14.5"300BLK supers – 7"300BLK subs – 5"300WM – 20"300RUM – 24" Firing ScheduleStainless Enticer cans are not Full Auto rated. With that being said, stainless versions can handle 120 rounds 556 rapid fire / full auto before needing a cool down period.

Black Cerakote FinishDDC Enticer cans come with a removable end cap which is compatible with Dead Air end caps.Enticer cans also come threaded with 1-3/8?x24.  What does 1-3/8×24 thread mean for you?  This thread allows you to run a wide variety of mounts such as: Direct thread adapters, Q Plan B/Cherry Bomb, Keymo and Rearden Atlas.Pew Science results:Enticer L and LTi series cans are currently the quietest can at ear on .308 that has been tested.  They have an overall composite suppression rating of 51.9. (S and STi are 42.5).Firing schedule:Titanium Enticer cans are not Full Auto rated.  With that being said, titanium versions can handle 50 rounds 556 rapid fire / full auto before needing a cool down period.What you get:-A kick ass suppressor-DDC sticker-5/8?x24 titanium direct thread adapter-No BS lifetime warranty when following barrel length and firing schedules. Caliber7.62 NATO300BK300WMAny caliber smaller Diameter1-5/8 (1.625”)Weight10.5oz with included mountOverall Length8-1/4”Material100% CNC machined 6-4 titanium laser weldedCommon min barrel lengths:556 – 10.5"308 – 14.5"300BLK supers – 7"300BLK subs – 5"300WM – 20"300RUM – 24"Please contact mfg for info on any other caliber you may be shooting that are not similar to the above list 

Enticer L-Ti Mill FinishDDC Enticer cans come with a removable end cap which is compatible with Dead Air end caps.Enticer cans also come threaded with 1-3/8?x24.  What does 1-3/8×24 thread mean for you?  This thread allows you to run a wide variety of mounts such as: Direct thread adapters, Q Plan B/Cherry Bomb, Keymo and Rearden Atlas.Pew Science results:Enticer L and LTi series cans are currently the quietest can at ear on .308 that has been tested.  They have an overall composite suppression rating of 51.9. (S and STi are 42.5).Firing schedule:Titanium Enticer cans are not Full Auto rated.  With that being said, titanium versions can handle 50 rounds 556 rapid fire / full auto before needing a cool down period.What you get:-A kick ass suppressor-DDC sticker-5/8?x24 titanium direct thread adapter-No BS lifetime warranty when following barrel length and firing schedules. Caliber7.62 NATO300BK300WMAny caliber smaller Diameter1-5/8 (1.625”)Weight10.5oz with included mountOverall Length8-1/4”Material100% CNC machined 6-4 titanium laser weldedCommon min barrel lengths:556 – 10.5"308 – 14.5"300BLK supers – 7"300BLK subs – 5"300WM – 20"300RUM – 24"Please contact mfg for info on any other caliber you may be shooting that are not similar to the above list

DescriptionThe Diligent Defense Enticer S can comes with a removable end cap which is compatible with Dead Air end caps.Enticer cans also come threaded with 1-3/8"x24. What does 1-3/8×24 thread mean for you? This thread allows you to run a wide variety of mounts such as: Direct thread adapters, Q Plan B/Cherry Bomb, Keymo and Rearden Atlas. Enticer S SpecsCaliber: 7.62 NATO/ 300BK / 300WM or any caliber smallerDiameter: 1-5/8 (1.625”)Weight: 13.8oz with included mountOverall Length: 6-3/4”Material: 100% CNC machined 17-4 Stainless laser welded & heat treatedCommon Min Barrel Lengths556 – 10.5"308 – 14.5"300BLK supers – 7"300BLK subs – 5"300WM – 20"300RUM – 24" Firing ScheduleStainless Enticer cans are not Full Auto rated. With that being said, stainless versions can handle 120 rounds 556 rapid fire / full auto before needing a cool down period.

Enticer S Ti SpecsCaliber: 7.62 NATO/ 300BK / 300WM or any caliber smallerDiameter: 1-5/8 (1.625”)Weight: 9.3oz with included mountOverall Length: 6-3/4?Material: 100% CNC machined 6-4 titanium laser weldedCommon Min Barrel Lengths556 – 10.5?308 – 14.5?300BLK supers – 7?300BLK subs – 5?300WM – 20?300RUM – 24? Firing ScheduleTitanium Enticer cans are not Full Auto rated. With that being said, titanium versions can handle 50 rounds 556 rapid fire / full auto before needing a cool down period.

 100% titanium constructed 22LR suppressor that performs great on rifle or pistol hosts.Covers 22LR, .17HMR, 5.7 and .22WMR.Fully serviceable via removing the DTA and or end cap.Features Keyed and labelled baffles to aid in reassembly after cleaning.Ultra light weight at just 4.5oz.Overall length is 5-3/16?1/2? x 28 mounting threads

 The Wolf Hunter Suppressor is our 6mm hunting can. It’s best used where maximum suppression is needed in a light weight package.It’s compact length (6-3/4?) allows great performance on calibers 6mm and below.Wolf Hunter SpecsCalibers: Up to 6mm (bore 0.281?)Material: TitaniumLength: 6-3/4?Diameter: 1-5/8?Mounting options: Anything Bravo or 1-3/8×24 threadWeight: 9.1ozDirect thread included: 1/2?x28 and 5/8?x24Finish: Graphite BlackPrice: $800 MSRPCommon Min Barrel Lengths6mm and 556 – 10-1/2? Firing ScheduleThis suppressor is made from Titanium to keep the weight down. It is very strong but subject to strength loss at high heat. We recommend to keep Suppressor below 800 degrees.

What sets The Mask™ apart is its marvelous performance and the ease with which it can be disassembled. With little to no first-round-pop on both rifles and pistols, it provides a balance of performance, weight, and extraordinary cleaning intervals that are unmatched by the competition.This isn’t a “me too” compulsory foray into the .22 suppressor market. We wanted the best and we delivered. The performance speaks for itself. Our .22 suppressor features a blend of titanium and 17-4 PH stainless steel construction for direct thread applications. Caliber Rating.22LR, 22MAG, 17HMR,  17WSM to 5.7×28Energy Rating850 ft lbsBore Diameter.22 caliberLength5.1 inchesDiameter1.070 inchesWeight6.6 ouncesMaterials17-4 Stainless Steel Baffles, Titanium 3Al-2.5V Grade 9 TubeFinishBlack or FDE Cerakote® or Satin bead-blastedUsageHeavy-duty use rimfire suppressorBarrel RestrictionsNoneFull Auto RatedYes

FLOW 22 TIA new dimension of rimfire suppression – The FLOW 22 Ti is the lightest and quietest Flow-Through® suppressor to come from HUXWRX Safety Co. Completely 3D-printed in Grade 5 Titanium, the FLOW 22 Ti is lightweight, versatile, and extremely durable. Built with the latest advancements on our patented and proven Flow-Through® technology, it effectively delivers toxic fume mitigation, improved sound performance, and increased accuracy with excellent repeatability. This suppressor comes direct thread ready in 1/2x28, offers a cleaner shooting experience, and requires no general modifications to the weapon system. The FLOW 22 Ti is full-auto rated and cross platform compatible for 17 HMR, 22 LR, 22 Magnum, and 5.7 with no barrel length restrictions. This suppressor is ideal for competition shooters, hunting enthusiasts, and individuals seeking a top-tier rimfire build.

FLOW 556 TiLightweight and long-lasting, the FLOW 556 Ti is the latest advancement in Flow-Through® technology. Entirely 3D-printed with Grade 5 titanium, the FLOW 556 Ti is the quietest full-size 5.56 dedicated suppressor to come from HUXWRX Safety Co. without sacrificing quality, longevity, durability, or functionality. This innovative suppressor utilizes patented and proven Flow-Through® and Torque Lock® technologies delivering exceptional toxic fume mitigation, accuracy, and repeatability. The integrated GeoFlash™ Cap geometry mitigates flash as part of its overall signature reduction functionality. The first full-size 5.56 suppressor from the FLOW series is full-auto rated with no barrel restrictions. No modifications (other than QD muzzle device) to the platform or gas system are required to install or operate this suppressor. HUXWRX FLOW Series suppressors are the future of suppression—Compromise Elsewhere. Compatible with Muzzle Brake-QD 556 and Flash Hider-QD 556

FLOW 556KAn innovative multi-caliber suppressor with patented and proven Flow-Through® and Torque Lock® technology. It is designed to reduce signature without negatively impacting cycling or service life. The FLOW 556k is DMLS printed in 17-4 Stainless. It delivers superior toxic fume exposure mitigation, flash reduction, sound reduction, recoil reduction, accuracy, and repeatability by its unique Flow-Through® helical coil and core deflector design. It is full-auto rated and compatible on 5.56, 17 HMR, and 5.7 platforms. The integrated GeoFlash™ Cap geometry effectively mitigates flash as part of its overall signature reduction funtionality. Compatible with Muzzle Brake-QD 556 and Flash Hider-QD 556. *Does NOT Come with muzzle device. Silencer ONLY

FLOW 556KAn innovative multi-caliber suppressor with patented and proven Flow-Through® and Torque Lock® technology. It is designed to reduce signature without negatively impacting cycling or service life. The FLOW 556k is DMLS printed in 17-4 Stainless. It delivers superior toxic fume exposure mitigation, flash reduction, sound reduction, recoil reduction, accuracy, and repeatability by its unique Flow-Through® helical coil and core deflector design. It is full-auto rated and compatible on 5.56, 17 HMR, and 5.7 platforms. The integrated GeoFlash™ Cap geometry effectively mitigates flash as part of its overall signature reduction funtionality. Compatible with Muzzle Brake-QD 556 and Flash Hider-QD 556.

DUAL-LOK™ HRT 556™ Specs:DIMS: 1.5”x 5.9”Weight: 14.4ozKey points :Wear free mounting system, requires no consumable partsTaper lock interface ensures security and accuracyACME thread provides speed of attachmentLocking ring incorporates 3 anti-rotation teeth to eliminate inadvertent loosening120 effective positions ensure a rock-solid suppressor mount and provide extremely low POI shift17-4 stainless steel & 718 Inconel constructionTraditional Tube Design with internal flash hiding characteristicsPatent pending ECO-FLOW™ baffle system for reduced blow backPatented flash reducing end cap¾” wrench flats on muzzle devicesCollar Nitrided black for increased surface hardness, corrosion, and wear resistanceHeat treated and Cerakoted Black and FDE in a heat resistant finishWarrantied for life with Griffin’s Perpetual Lifetime Warranty

The Hybrid 46M is intended to provide the everyday shooter with one suppressor that has the capability of effectively suppressing as many firearm types and calibers as possible at a very affordable price point, while also giving the customer the most highly sought after features in suppressor design, such as modularity and accessory compatibility.The Hybrid 46M is a light, compact, modular centerfire rifle suppressor, with the versatility to use on magnum rifles, pistols, and subguns.  Both configurations are full-auto rated.The Hybrid 46M is rated for all centerfire pistol and rifle calibers including 45 Auto, 10MM, .450 Bushmaster, .458 SOCOM, .45-70, .338 LM and up to .460 Weatherby Magnum.Designed for versatility across multiple platforms with a balance for weight and performance.Includes Charlie ASR Mount and Charlie .30 cal front cap. Compatible with the Charlie ASR Mount, all Charlie Direct Thread Mounts, Charlie Piston Mount, all Charlie Front Caps, all ASR Muzzle Devices, Pistons and Tri-Lug.Short Configuration: weighs 12.2 oz. & Measures 5.78 inches (without mount)Long Configuration: weighs 14.9 oz. & Measures 7.72 inches (without mount)Rated for all centerfire pistol and rifle calibers including 45 Auto, 10MM, 450 Bushmaster, 458 SOCOM, 45-70, 338 LM and up to 460 Weatherby Magnum.Constructed of Titanium, Inconel and 17-4 Heat Treated Stainless SteelFull-Auto Rated

HYPERION-QD 7.62Overall Length9.5"Weight15.1ozDiameter1.75"MaterialsDirect metal laser sintered (DMLS – 3d printed) heat treated grade 5 titanium

These come equipped with a Rearden Atlas thread adapter, and include a 1/2-28 LPM Eclipse flash hider, and a 5/8-24 LPM Liberty Bell muzzle brake.The Anthem 2 series of .30 caliber rifle silencers is an evolution of the original Anthem series silencers from Liberty Precision Machine LLC. With lessons learned through the development of our other product lines, we have refreshed the Anthem baffle stack to achieve better performance, lighter weight, and an even lower price!The Anthem 2 silencers are designed around the following requirements, in order of importance:Maximum sound reduction for a given lengthMaximum strength for a given weightNo negative impact on accuracy Maximum visible flash signature reductionLow blowback for gas operated firearmsProgressive baffle design and spacing allows us to tune the silencer for the various pressure regimes and gas dynamics experienced over the length of the silencer. The Anthem 2 series of silencers have market leading efficiency across many cartridges and firearm hosts.Features and Specs:1.74? Diameter6.85? long (no rear mount), 7.35? with included Rearden Atlas14.2 ounces (no rear mount), 15.8 ounces with included Rearden AtlasGraphite Black Cerakote™ finishFull-auto ratedNo barrel length restrictions on any .30 caliber (or less) cartridgeRemovable front end cap with 3/4? socketLifetime warranty guarantees our products to be free from defects in workmanship and materials. This warranty covers everything except willful destruction and normal wear and tear

The LPM DUTY 5.56 was designed to provide high holistic signature reduction for both operators and bystanders on gas-operated firearms. This requires moderate gas blowback and sound to the shooter while maintaining a high level of muzzle sound suppression. A simplified version of our Torch 5.56/6mm silencer, the DUTY achieves a much lower price point and smaller size for budget minded shooters who are willing to tolerate slightly more back pressure and gas blowback. Tuning of the host weapon is recommended. LPM highly recommends AGAINST the CAT SPOOKY 1 flash hider as it results in premature baffle wear and excess flash out of the silencer. No other muzzle device we have tested has displayed these characteristics. Model: DUTY 5.56SKU: LPM-10023Weight 11.7 oz (No mount)Length: 5.1? (No mount)Diameter: 1.75?Thread Pitch: Universal 1.375-24 TPI pattern mounting system, ships with DLC titanium 1/2-28 direct thread adapter (.9 oz)End caps: SolidCaliber Rating: Up to 6mm, full-auto ratedMinimum Barrel Length: 7.5?Finish: Graphite Black Cerakote™Warranty: Lifetime warranty for workmanship and material defects. This warranty covers everything except willful destruction and normal wear and tear

The Mach series of .30 caliber rifle silencers is an evolution of the original Anthem series silencers from Liberty Precision Machine LLC. With lessons learned through the development of our other product lines, we have refreshed the  baffle stack to achieve better performance. The Mach series of silencers has an identical baffle stack to the Anthem 2 series, just in Titanium!The Mach silencers are designed around the following requirements, in order of importance:Maximum sound reduction for a given lengthMaximum strength for a given weightNo negative impact on accuracy Maximum visible flash signature reductionLow blowback for gas operated firearmsProgressive baffle design and spacing allows us to tune the silencer for the various pressure regimes and gas dynamics experienced over the length of the silencer. The Mach series of silencers have market leading efficiency across many cartridges and firearm hosts.Features and Specs:1.74? Diameter9.1? long (no rear mount), 9.25? with included 5/8-24 Rearden DTA Ti direct thread adapter11.9 ounces (no rear mount), 12.7 ounces with included 5/8-24 Rearden DTA Ti direct thread adapterGraphite Black Cerakote™ finishNo barrel length restrictions on any .30 caliber (or less) cartridge, muzzle brake recommended for barrels shorter than 14.5?Removable front end cap with 3/4? socketLifetime warranty guarantees our products to be free from defects in workmanship and materials. This warranty covers everything except willful destruction and normal wear and tear

The LPM Torch was designed to provide extreme holistic signature reduction for both operators and bystanders on gas-operated firearms. This requires minimal gas blowback and sound to the shooter while maintaining a high level of muzzle sound suppression. Solid and vented end caps are included to allow for changing the bias of muzzle to ear sound suppression depending on the host weapon and user needs. The innovative nested blast baffle design increases strength, reduces baffle erosion on short barrels, and minimizes the silencer’s effect on weapon function.Model: Torch QDSKU: LPM-10010Weight 14.0 oz (No mount)Length: 6.2" (No mount)Diameter: 1.75"Thread Pitch: Universal 1.375-24 TPI pattern mounting system, ships with Rearden Atlas QD mount and one (1) LPM Eclipse Flash Hider in ½-28End caps: Vented Flash Hiding and SolidCaliber Rating: Up to 6mm, full-auto ratedMinimum Barrel Length: 7.5"Finish: Graphite Black Cerakote™Warranty: Lifetime warranty for workmanship and material defects. This warranty covers everything except willful destruction and normal wear and tear

What sets The Mask™ apart is its marvelous performance and the ease with which it can be disassembled. With little to no first-round-pop on both rifles and pistols, it provides a balance of performance, weight, and extraordinary cleaning intervals that are unmatched by the competition.This isn’t a “me too” compulsory foray into the .22 suppressor market. We wanted the best and we delivered. The performance speaks for itself. Our .22 suppressor features a blend of titanium and 17-4 PH stainless steel construction for direct thread applications. Caliber Rating.22LR, 22MAG, 17HMR,  17WSM to 5.7×28Energy Rating850 ft lbsBore Diameter.22 caliberLength5.1 inchesDiameter1.070 inchesWeight6.6 ouncesMaterials17-4 Stainless Steel Baffles, Titanium 3Al-2.5V Grade 9 TubeFinishBlack or FDE Cerakote® or Satin bead-blastedUsageHeavy-duty use rimfire suppressorBarrel RestrictionsNoneFull Auto RatedYesPart NumberMASK22

What sets The Mask™ apart is its marvelous performance and the ease with which it can be disassembled. With little to no first-round-pop on both rifles and pistols, it provides a balance of performance, weight, and extraordinary cleaning intervals that are unmatched by the competition.This isn’t a “me too” compulsory foray into the .22 suppressor market. We wanted the best and we delivered. The performance speaks for itself. Our .22 suppressor features a blend of titanium and 17-4 PH stainless steel construction for direct thread applications.  Caliber Rating.22LR, 22MAG, 17HMR,  17WSM to 5.7×28Energy Rating850 ft lbsBore Diameter.22 caliberLength5.1 inchesDiameter1.070 inchesWeight6.6 ouncesMaterials17-4 Stainless Steel Baffles, Titanium 3Al-2.5V Grade 9 TubeFinishBlack or FDE Cerakote® or Satin bead-blastedUsageHeavy-duty use rimfire suppressorBarrel RestrictionsNoneFull Auto RatedYes

Caliber Rating.33XCEnergy Rating6800 ft lbsLength9.1” (Body), 9.60” (w/Xemax Adapter)Diameter1.75 inchesWeight12.9 oz (Body), 15.4 oz (w/Xemax Adapter)MaterialsGrade 5 6A1-4V TitaniumFinishRaw titanium satin bead-blasted, black, or FDE high temp Cerakote®, Nitride adapter and mountUsageBolt-action, semi-auto. For ultimate sound reduction and weight savings.MountXemax Brake/Adapter, Dead Air HUB CompatibleBarrel Restrictions18” (.338 Lapua)Full Auto RatedNo

The Obsidian45 is one of the quietest 45 suppressors on the market and is rated for practically all center-fire pistol calibers, along with common lever action calibers. Our ADAPT™ Module gives you 2 lengths in one suppressor, for ultimate versatility. Obsidian45™ Caliber RatingsBelt Fed Rated for Pistol Calibers up-to 45ACP300BLK Subsonic (with an 8? barrel)350 Legend (with a 16? barrel or longer)450 Bushmaster (with a 16? barrel or longer) Obsidian45™ SpecificationsDiameter: 1.37?Length: Standard Configuration: 8.6?, Short Configuration: 6.7?Weight: Standard Configuration: 12.8oz; Short Configuration: 10.7oz MaterialsBaffles: 17-4 Stainless SteelTube: Hard Coat Anodized AluminumMount: 17-4 Stainless SteelFinish: High Temp Cerakote® (Black or FDE)

BYOM – Buy Your Own Mount. This suppressor does not come with a mount, this suppressor does not come with a mount, this suppressor does not come with a mount. If you email me and say “Hey man I just got my infinity out of jail and there’s no mount in the box” I’m going to make fun of you, just keeping it real. We surveyed around 3000 customers and 78% of them said they don’t use the direct thread mounts that usually come in the box with suppressors. They throw it in a parts box to be forgotten or throw it away and buy their own mounting system. So we decided to just not include a direct thread mount with the infinity so we could reduce the cost and you’re not paying for something you’re not going to use. It’s already an expensive suppressor, no need to add to that cost unnecessarily. It is 1.375×24 HUB threaded which is the industry standard universal mounting system. There’s hundreds of combinations of mounts and stuff that work in this suppressor, if you need help picking one out feel free to email us. Infinity — We decided to call this project Infinity early on because we wanted this to be a suppressor that will last you forever, you can pass down to your grandchildren and it last them forever too. Also because of it’s adjustability and ability to be configured to any host you have. It’s also marks our entry into the low back pressure market. Notice I didn’t say no back pressure, I said lowER back pressure. We wanted this suppressor to straddle the line of suppressors with zero back pressure that sound like a pipe bomb and suppressors with high back pressure that sound great. There’s no free lunch when it comes to sound suppression. You either have a suppressor that’s loud with zero gas to the face or you have a suppressor that’s quiet with some uncomfortable gas to the face, it just is what it is. We wanted a suppressor that could ride the middle ground line and venture to both sides of the line depending on what the user wanted. There’s all kinds of fancy marketing words you could come up with for it that will make you sound smart. Hybrid adjustable flow path technology being calculated by a super computer in a lab and optimized by an AI program in real time. Engineers applying echolocation quantum mechanics for the absolute refraction of performance. Don’t forget to throw something about aerospace or secret military teams and operators in there somewhere. But it’s all so generic, predictable, typical, boring and most of all… bull shit. So let’s cut through the bull shit and get down to the nitty gritty of what this suppressor does and what makes it unique. We knew we wanted it to be 7.62 bore with changeable end caps. We knew we wanted it to have great 7.62 performance but let’s not kid ourselves, 99% of users buying a 7.62 bore suppressor are using it on 5.56 most of the time. So the 5.56 performance also had to be on point. We developed the general sound profile using 7.62 and then further dialed it in and refined it using 5.56 – we made over 100 prototypes in almost 2 years of testing finding just the right combination that does just as good on 5.56 as an actual 5.56 bore suppressor while still offering great 7.62 performance AND works well being vented or unvented. It has 3 different end caps that come in the box to adjust the back pressure and flow rate based on what host you want to use it on. Additional end caps are available for purchase separately. Other suppressors in the past have tried this idea, adjusting back pressure by changing end caps that allow it to vent from other chambers. But in our opinion they didn’t do a good job – great idea but poor execution. So we wanted to take that idea and make it good and I believe we’ve done that. How we did it is the inside of the infinity is actually divided up into 4 chambers. The first initial expansion chamber vents gas straight off of the muzzle as it enters the suppressor > the second is a high back pressure chamber that holds the gas while allowing a small amount of controlled flow into the third chamber > the third chamber is where gasses coming down the bore and gasses from the high back pressure chamber combine before going into the fourth chamber > the fourth and final chamber is a low back pressure high flow rate zone that moves gasses down the side wall. When you use the vented end cap it’s only venting gasses out of the fourth chamber which allows it to be very balanced. When using the vented end cap the pattern is vent > hold > combine > vent. When using the solid end cap the pattern is vent > hold > combine > hold. Solid 5.56 end cap (included in box) — The highest back pressure setting for this suppressor. Sound suppression similar to a Polonium or Polonium-K and depending on the host you might need to tune it. BUT if you’re one of those people who don’t care to tune a gun and you want max quiet on your 5.56 rifles this is the end cap you’ll want to use. It offers excellent sound performance and flash reduction. It can also be used on 6mm/243 bolt action rifles. Vented 7.62 end cap (included in box) — The lowEST back pressure setting for this suppressor. If you are running on a back pressure sensitive 5.56 host or any semi auto 7.62 rifle this is the end cap you want to be using. This end cap is going to be for your MCX, Scar, AR10, Tavor, AK platform guns and over gassed AR15 pattern guns with gas ports so gaped it would make a pornstar blush. Basically any gun or any use case where you want the least amount of back pressure this is the end cap you want to be using. Solid 7.62 end cap (included in box) — This is the goldilocks end cap, the middle child. It’s right between the other two we just went over. On 5.56 rifles it offers a medium back pressure setting and works great on guns that aren’t gas sensitive but aren’t necessarily tuned either. This is also the end cap you’re going to want to use on 6.5mm, 7mm or 7.62mm bolt guns or subsonic 300 blackout. Vented 5.56 end cap (available for purchase separately) — This is kind of a niche end cap. It reduces back pressure when compared to the 5.56 solid end cap or 7.62 solid end cap but not as much as the 7.62 vented end cap. If you have a gun where it needs to be a little less back pressure than the 5.56 solid but a little more back pressure than the 7.62 vented this fills that gap. Most users will not need this end cap in our opinion which is why it’s not included. So there you have it, that’s the end cap system explained and you have an end cap to optimize the suppressor for just about whatever you want to do with it. Changing end caps is quick and easy and comes with a wrench in the box to do it with. Being made from DMLS 3D printed & heat treated 718 inconel this thing is tough as nails. No barrel length restrictions, no firing schedule restrictions on magazine fed guns. On belt fed 5.56 guns we recommend not exceeding a 300 round solid string of non stop fire without a cool down period. On 7.62 belt fed guns we do not recommend exceeding a 200 round solid string of non stop fire without a cooldown period. If you are running it on a belt fed you need to be using the vented end cap. This suppressor has been tested to the most brutal extremes we can think of and has handled anything we’ve thrown at it. Yea yea yea it’s a little on the “heavy” side, there’s plenty of lightweight less durable options if that’s your thing. But this thing is built to last.  SpecsLength: 6.5” (no mount)Weight: 20 oz (no mount)Diameter/OD: 1.75”Material: Suppressor is DMLS 3D printed & heat treated 718 inconel, end caps are machined H900 17-4 stainless steel.Rear thread pattern: 1.375×24 HUBWhat’s included in the box? Suppressor, 3 end caps, tube clamp, end cap wrench.

BYOM – Buy Your Own Mount. This suppressor does not come with a mount, this suppressor does not come with a mount, this suppressor does not come with a mount. If you email me and say “Hey man I just got my infinity out of jail and there’s no mount in the box” I’m going to make fun of you, just keeping it real. We surveyed around 3000 customers and 78% of them said they don’t use the direct thread mounts that usually come in the box with suppressors. They throw it in a parts box to be forgotten or throw it away and buy their own mounting system. So we decided to just not include a direct thread mount with the infinity so we could reduce the cost and you’re not paying for something you’re not going to use. It’s already an expensive suppressor, no need to add to that cost unnecessarily. It is 1.375×24 HUB threaded which is the industry standard universal mounting system. There’s hundreds of combinations of mounts and stuff that work in this suppressor, if you need help picking one out feel free to email us. Infinity — We decided to call this project Infinity early on because we wanted this to be a suppressor that will last you forever, you can pass down to your grandchildren and it last them forever too. Also because of it’s adjustability and ability to be configured to any host you have. It’s also marks our entry into the low back pressure market. Notice I didn’t say no back pressure, I said lowER back pressure. We wanted this suppressor to straddle the line of suppressors with zero back pressure that sound like a pipe bomb and suppressors with high back pressure that sound great. There’s no free lunch when it comes to sound suppression. You either have a suppressor that’s loud with zero gas to the face or you have a suppressor that’s quiet with some uncomfortable gas to the face, it just is what it is. We wanted a suppressor that could ride the middle ground line and venture to both sides of the line depending on what the user wanted. There’s all kinds of fancy marketing words you could come up with for it that will make you sound smart. Hybrid adjustable flow path technology being calculated by a super computer in a lab and optimized by an AI program in real time. Engineers applying echolocation quantum mechanics for the absolute refraction of performance. Don’t forget to throw something about aerospace or secret military teams and operators in there somewhere. But it’s all so generic, predictable, typical, boring and most of all… bull shit. So let’s cut through the bull shit and get down to the nitty gritty of what this suppressor does and what makes it unique. We knew we wanted it to be 7.62 bore with changeable end caps. We knew we wanted it to have great 7.62 performance but let’s not kid ourselves, 99% of users buying a 7.62 bore suppressor are using it on 5.56 most of the time. So the 5.56 performance also had to be on point. We developed the general sound profile using 7.62 and then further dialed it in and refined it using 5.56 – we made over 100 prototypes in almost 2 years of testing finding just the right combination that does just as good on 5.56 as an actual 5.56 bore suppressor while still offering great 7.62 performance AND works well being vented or unvented. It has 3 different end caps that come in the box to adjust the back pressure and flow rate based on what host you want to use it on. Additional end caps are available for purchase separately. Other suppressors in the past have tried this idea, adjusting back pressure by changing end caps that allow it to vent from other chambers. But in our opinion they didn’t do a good job – great idea but poor execution. So we wanted to take that idea and make it good and I believe we’ve done that. How we did it is the inside of the infinity is actually divided up into 4 chambers. The first initial expansion chamber vents gas straight off of the muzzle as it enters the suppressor > the second is a high back pressure chamber that holds the gas while allowing a small amount of controlled flow into the third chamber > the third chamber is where gasses coming down the bore and gasses from the high back pressure chamber combine before going into the fourth chamber > the fourth and final chamber is a low back pressure high flow rate zone that moves gasses down the side wall. When you use the vented end cap it’s only venting gasses out of the fourth chamber which allows it to be very balanced. When using the vented end cap the pattern is vent > hold > combine > vent. When using the solid end cap the pattern is vent > hold > combine > hold. Solid 5.56 end cap (included in box) — The highest back pressure setting for this suppressor. Sound suppression similar to a Polonium or Polonium-K and depending on the host you might need to tune it. BUT if you’re one of those people who don’t care to tune a gun and you want max quiet on your 5.56 rifles this is the end cap you’ll want to use. It offers excellent sound performance and flash reduction. It can also be used on 6mm/243 bolt action rifles. Vented 7.62 end cap (included in box) — The lowEST back pressure setting for this suppressor. If you are running on a back pressure sensitive 5.56 host or any semi auto 7.62 rifle this is the end cap you want to be using. This end cap is going to be for your MCX, Scar, AR10, Tavor, AK platform guns and over gassed AR15 pattern guns with gas ports so gaped it would make a pornstar blush. Basically any gun or any use case where you want the least amount of back pressure this is the end cap you want to be using. Solid 7.62 end cap (included in box) — This is the goldilocks end cap, the middle child. It’s right between the other two we just went over. On 5.56 rifles it offers a medium back pressure setting and works great on guns that aren’t gas sensitive but aren’t necessarily tuned either. This is also the end cap you’re going to want to use on 6.5mm, 7mm or 7.62mm bolt guns or subsonic 300 blackout. Vented 5.56 end cap (available for purchase separately) — This is kind of a niche end cap. It reduces back pressure when compared to the 5.56 solid end cap or 7.62 solid end cap but not as much as the 7.62 vented end cap. If you have a gun where it needs to be a little less back pressure than the 5.56 solid but a little more back pressure than the 7.62 vented this fills that gap. Most users will not need this end cap in our opinion which is why it’s not included. So there you have it, that’s the end cap system explained and you have an end cap to optimize the suppressor for just about whatever you want to do with it. Changing end caps is quick and easy and comes with a wrench in the box to do it with. Being made from DMLS 3D printed & heat treated 718 inconel this thing is tough as nails. No barrel length restrictions, no firing schedule restrictions on magazine fed guns. On belt fed 5.56 guns we recommend not exceeding a 300 round solid string of non stop fire without a cool down period. On 7.62 belt fed guns we do not recommend exceeding a 200 round solid string of non stop fire without a cooldown period. If you are running it on a belt fed you need to be using the vented end cap. This suppressor has been tested to the most brutal extremes we can think of and has handled anything we’ve thrown at it. Yea yea yea it’s a little on the “heavy” side, there’s plenty of lightweight less durable options if that’s your thing. But this thing is built to last.  SpecsLength: 6.5” (no mount)Weight: 20 oz (no mount)Diameter/OD: 1.75”Material: Suppressor is DMLS 3D printed & heat treated 718 inconel, end caps are machined H900 17-4 stainless steel.Rear thread pattern: 1.375×24 HUBWhat’s included in the box? Suppressor, 3 end caps, tube clamp, end cap wrench.

BYOM – Buy Your Own Mount. This suppressor does not come with a mount, this suppressor does not come with a mount, this suppressor does not come with a mount. If you email me and say “Hey man I just got my infinity out of jail and there’s no mount in the box” I’m going to make fun of you, just keeping it real. We surveyed around 3000 customers and 78% of them said they don’t use the direct thread mounts that usually come in the box with suppressors. They throw it in a parts box to be forgotten or throw it away and buy their own mounting system. So we decided to just not include a direct thread mount with the infinity so we could reduce the cost and you’re not paying for something you’re not going to use. It’s already an expensive suppressor, no need to add to that cost unnecessarily. It is 1.375×24 HUB threaded which is the industry standard universal mounting system. There’s hundreds of combinations of mounts and stuff that work in this suppressor, if you need help picking one out feel free to email us. Infinity — We decided to call this project Infinity early on because we wanted this to be a suppressor that will last you forever, you can pass down to your grandchildren and it last them forever too. Also because of it’s adjustability and ability to be configured to any host you have. It’s also marks our entry into the low back pressure market. Notice I didn’t say no back pressure, I said lowER back pressure. We wanted this suppressor to straddle the line of suppressors with zero back pressure that sound like a pipe bomb and suppressors with high back pressure that sound great. There’s no free lunch when it comes to sound suppression. You either have a suppressor that’s loud with zero gas to the face or you have a suppressor that’s quiet with some uncomfortable gas to the face, it just is what it is. We wanted a suppressor that could ride the middle ground line and venture to both sides of the line depending on what the user wanted. There’s all kinds of fancy marketing words you could come up with for it that will make you sound smart. Hybrid adjustable flow path technology being calculated by a super computer in a lab and optimized by an AI program in real time. Engineers applying echolocation quantum mechanics for the absolute refraction of performance. Don’t forget to throw something about aerospace or secret military teams and operators in there somewhere. But it’s all so generic, predictable, typical, boring and most of all… bull shit. So let’s cut through the bull shit and get down to the nitty gritty of what this suppressor does and what makes it unique. We knew we wanted it to be 7.62 bore with changeable end caps. We knew we wanted it to have great 7.62 performance but let’s not kid ourselves, 99% of users buying a 7.62 bore suppressor are using it on 5.56 most of the time. So the 5.56 performance also had to be on point. We developed the general sound profile using 7.62 and then further dialed it in and refined it using 5.56 – we made over 100 prototypes in almost 2 years of testing finding just the right combination that does just as good on 5.56 as an actual 5.56 bore suppressor while still offering great 7.62 performance AND works well being vented or unvented. It has 3 different end caps that come in the box to adjust the back pressure and flow rate based on what host you want to use it on. Additional end caps are available for purchase separately. Other suppressors in the past have tried this idea, adjusting back pressure by changing end caps that allow it to vent from other chambers. But in our opinion they didn’t do a good job – great idea but poor execution. So we wanted to take that idea and make it good and I believe we’ve done that. How we did it is the inside of the infinity is actually divided up into 4 chambers. The first initial expansion chamber vents gas straight off of the muzzle as it enters the suppressor > the second is a high back pressure chamber that holds the gas while allowing a small amount of controlled flow into the third chamber > the third chamber is where gasses coming down the bore and gasses from the high back pressure chamber combine before going into the fourth chamber > the fourth and final chamber is a low back pressure high flow rate zone that moves gasses down the side wall. When you use the vented end cap it’s only venting gasses out of the fourth chamber which allows it to be very balanced. When using the vented end cap the pattern is vent > hold > combine > vent. When using the solid end cap the pattern is vent > hold > combine > hold. Solid 5.56 end cap (included in box) — The highest back pressure setting for this suppressor. Sound suppression similar to a Polonium or Polonium-K and depending on the host you might need to tune it. BUT if you’re one of those people who don’t care to tune a gun and you want max quiet on your 5.56 rifles this is the end cap you’ll want to use. It offers excellent sound performance and flash reduction. It can also be used on 6mm/243 bolt action rifles. Vented 7.62 end cap (included in box) — The lowEST back pressure setting for this suppressor. If you are running on a back pressure sensitive 5.56 host or any semi auto 7.62 rifle this is the end cap you want to be using. This end cap is going to be for your MCX, Scar, AR10, Tavor, AK platform guns and over gassed AR15 pattern guns with gas ports so gaped it would make a pornstar blush. Basically any gun or any use case where you want the least amount of back pressure this is the end cap you want to be using. Solid 7.62 end cap (included in box) — This is the goldilocks end cap, the middle child. It’s right between the other two we just went over. On 5.56 rifles it offers a medium back pressure setting and works great on guns that aren’t gas sensitive but aren’t necessarily tuned either. This is also the end cap you’re going to want to use on 6.5mm, 7mm or 7.62mm bolt guns or subsonic 300 blackout. Vented 5.56 end cap (available for purchase separately) — This is kind of a niche end cap. It reduces back pressure when compared to the 5.56 solid end cap or 7.62 solid end cap but not as much as the 7.62 vented end cap. If you have a gun where it needs to be a little less back pressure than the 5.56 solid but a little more back pressure than the 7.62 vented this fills that gap. Most users will not need this end cap in our opinion which is why it’s not included. So there you have it, that’s the end cap system explained and you have an end cap to optimize the suppressor for just about whatever you want to do with it. Changing end caps is quick and easy and comes with a wrench in the box to do it with. Being made from DMLS 3D printed & heat treated 718 inconel this thing is tough as nails. No barrel length restrictions, no firing schedule restrictions on magazine fed guns. On belt fed 5.56 guns we recommend not exceeding a 300 round solid string of non stop fire without a cool down period. On 7.62 belt fed guns we do not recommend exceeding a 200 round solid string of non stop fire without a cooldown period. If you are running it on a belt fed you need to be using the vented end cap. This suppressor has been tested to the most brutal extremes we can think of and has handled anything we’ve thrown at it. Yea yea yea it’s a little on the “heavy” side, there’s plenty of lightweight less durable options if that’s your thing. But this thing is built to last.  SpecsLength: 6.5” (no mount)Weight: 20 oz (no mount)Diameter/OD: 1.75”Material: Suppressor is DMLS 3D printed & heat treated 718 inconel, end caps are machined H900 17-4 stainless steel.Rear thread pattern: 1.375×24 HUBWhat’s included in the box? Suppressor, 3 end caps, tube clamp, end cap wrench.

Bet you can’t guess what it’s made out of. Titanium, the 22nd element on periodic table of elements and we wanted to make our 22 LR silencer out of titanium anyway – it was just meant to be. They used titanium with the freaking SR71 blackbird and your grandmas knee replacement.Look we could play the game that the rest of the industry plays and tell you it metered at 17 dB only to have competitors start changing their website to say 16 dB the next day but otter don’t play no shit. In testing and development for this silencer we were bodying industry giants left and right. Our design goals were to have a simple, easy to use, easy to clean, light weight, small, quiet 22 suppressor with almost no first round pop at as low of a price point as we could possibly make it. No stupid, made up, trademarked marketing words, no paid glowing reviews from some youtuber who can’t wait to sell you the next $17 made in China flash light, just a straight forward no BS product that you can be happy you bought with your hard earned money and that we don’t have to squirt a bottle of KY Jelly in for it to blow your socks off every time.The rear mount of the Titanium is threaded 1/2×28 and is semi-permanently installed. That means it won’t accidently come off of the suppressor when you’re trying to take it on and off the gun but if it ever needs to come off for any reason it can be taken off by us. We also made the mount threads longer to accommodate some of the longer threaded rifle barrels so you can use it without having to use a stupid spacer or shim like you have to use with some other 22 suppressors. The wrench flats in the front and rear of the suppressor can be used with any cheapo $3 adjustable wrench from your local hardware store, that means no small proprietary tool or wrench for you to lose and have to buy for a second or third time. Because it’s titanium you can clean it however you want – ultra sonic cleaner, harsh chemical mixtures like “the dip”, tumble it with stainless pins, scrub it with a wire brush, whatever you want to do. The baffles have alignment tabs that only go together 1 way, there is no way to put it back together wrong or mess it up. The shielded baffle design keeps the tube walls clean and makes it very easy to slide the baffle stack out, clean it, put it back together and slide it back in.That really sums it up. It’s affordable, it’s light, it’s small, it’s quiet, it has little to no first round pop depending on host and ammo, it’s simple and sexy, it’s easy to take apart and clean then put back together and it’s better than whatever you’re using now in some way. There is no 22 suppressor that blends weight and sound like the Titanium 22. Backed by our lifetime warranty and awesome customer service what’s not to love? SPECSLength: 5.18?Weight: 4 ozMaterial: 100% TitaniumCALIBERS AND RESTRICTIONS Full auto rated for 22LRSemi auto rated for FN 5.7 – 17 HMR – 22 MAG and other similar calibers. If you have a question don’t hesitate to reach out and ask.WHAT’S IN THE BOX?The suppressor and some stickers, that’s it. This is a BYOW (buy your own wrench) situation. You should already have an adjustable wrench but if you don’t you can seriously get them at walmart for like $4.

SKUSU5184Caliber Compatibility9MM & 300 BLK SubsonicAccessoriesPistons & Fixed Barrel Spacer?Weight8.8 ozLength7.06??Diameter1.30 X 1.75??MaterialsAluminum & 17 – 4 SS?Ships WithShips with Disassembly Tool, Indexing Ring/Spring Retainer, and (1) Spring

The Ramblin Man is a lightweight, modular suppressor designed for versatility. It features a HUB mounting system and is compatible with R-Series front caps, allowing for easy customization. Offering class-leading sound suppression and weight savings, it is ideal for users seeking a one-suppressor solution for various firearms and shooting needs. Minimum Barrel Length & Caliber Restrictions22” – 300 RUM, 300 PRC, 300 Win20? – 6.5 PRC,  7mm Mag, 7mm PRC, 16” – 45-70 Govt, 30-06, 270 Win, 22-250 Rem14.5” – .308, 6.5 Creedmoor, .243 Win, 30-30, 7mm-0810.5” – 5.56/223, 6.5 Grendel, 6 ARC, 450 Bushmaster, 458 SOCOM8” – 8.6 Blackout,  7.62×39, 350 Legend7” – 300 Blackout Supersonic5” – 300 Blackout SubsonicNo barrel restrictions – 45ACP, 10mm, 9mm, 44 Mag, 45 Long Colt (full auto rated on pistol cartridges)*The Ramblin Man is a light-duty suppressor not intended for high rates of fire on centerfire rifle cartridges. For unspecified calibers, contact Resilient Suppressors. It must be kept under 750 degrees during use. We advise against the use of a flash hider with this suppressor.Length Long (without mount) – 7.72”Length Short (without mount) – 5.46”Weight Long (without mount) – 8.8 OuncesWeight Short (without mount) – 6 OuncesDiameter – 1.490”Coating – DLC (Mount) & High Temp Cerakote (Suppressor)Mount – 11/16 x 24 DTA (1.375×24 HUB Threads)Construction – 6AL-4V Titanium & CNC laser weldedAllowable Mounting Depth – 1.750”*Compatible with our Titanium Tri Lug and upcoming Titanium Booster Housing. 

The Oculus22 provides class leading suppression with 2 configurations in one suppressor. With 100% Stainless Steel construction, more cleaning solutions are available and durability is unmatched. Caliber Ratings22LR Belt Fed Rated®22 WMR17 HMR17 WSM5.7x28mm SpecificationsDiameter: 1.06?Length: Standard Configuration: 5.25?, Short Configuration: 3.25?Weight: Standard Configuration: 6.9oz; Short Configuration: 4.3oz MaterialsBaffles: 17-4 Stainless SteelTube: 17-4 Stainless SteelMount: 17-4 Stainless SteelFinish: High Temp Cerakote® (Black or FDE)

The Scythe-Ti is a .30 caliber suppressor, handling calibers ranging from .223 REM/5.56 NATO all the way up to .300 RUM. It’s intended for bolt-guns and semi-automatic rifles.It ships with a new radial tool, a Bravo tool, a basic tool, a 5/8 x 24 titanium direct thread mount, and a .30 cal aluminum Single-Port Anchor Brake.*Not rated for full-auto fire.*Lead projectiles are not recommended for use with any of our sealed suppressorsFeatures—Extremely lightweight and short for minimal impact on host weapon.—Features a new single-port anchor brake to reduce recoil and maintain minimum length.—Rated all the way up to .300 RUM with impressive sound suppression.—No barrel restrictions.—Bolt-gun and semi-auto rated — not rated for full-auto fire. —Type 2 Anodized with an oil rubbed finish.—Ships with a new radial tool, a Bravo tool, a basic tool, a 5/8 x 24 titanium direct thread mount, and a .30 cal Single-Port Anchor Brake.This is an exclusive black cerakote finish for Silencer shop